UNIPOWER APM10：千瓦變送器
尺寸：DxWxH = 58 x 36 x 86 mm
*三相對稱kW測量
*測量電壓：
3 x 100Vac-3 x 500Vac（一臺）
*電源電壓24Vdc
*使用內部CT直接測量高達60A
-否則外部CT N / 5
*精度：符合EN 61036的2級
* 6個電流范圍：5A，10A，20A，25A，40A，60A
* 0（4）-20mA或0（2）-10V模擬輸出
* CE標志
UNIPOWER APM10: kW-transmitter
* Dimensions: DxWxH = 58 x 36 x 86 mm
* 3-phased symmetric kW-measurement
* Measuring voltage:
3 x 100Vac - 3 x 500Vac with one unit
* Supply voltage 24Vdc
* Direct measurement up to 60A with internal CT
- otherwise external CT N/5
* Accuracy: Class 2 according to EN 61036
* 6 current ranges: 5A, 10A, 20A, 25A, 40A, 60A
* 0(4)-20mA or 0(2)-10V analogue outputs
UNIPOWER APM100B：千瓦測量傳感器
*尺寸：DxWxH = 58 x 70 x 86 mm
*三相對稱kW測量
*測量和電源電壓：
3 x 380Vac-3 x 500Vac帶一個單元
*通過內部CT直接測量高達80A
-否則外部CT N / 5
*精度：符合EN 61036的2級
*以kW為單位的范圍設置：
從0.1kW到70kW，以0.1kW為步長
* 0（4）-20mA以及0（2）-10V模擬輸出
* kWh輸出（SO-1）：
滿刻度100或300脈沖/小時
*內置濾波器功能-平均16倍
UNIPOWER APM100B: Measurement transducer for kW
* Dimensions: DxWxH = 58 x 70 x 86 mm
* 3-phased symmetric kW-measurement
* Measuring- and supply voltage:
3 x 380Vac - 3 x 500Vac with one unit
* Direct measurement up to 80A with internal CT
- otherwise external CT N/5
* Accuracy: Class 2 according to EN 61036
* Range setup in kW:
from 0.1kW to 70kW in steps of 0.1kW
* 0(4)-20mA as well as 0(2)-10V analogue outputs
* kWh-output (SO-1):
100 or 300 pulses/hour at full scale
* Built-in filter function - 16x averaging
* CE-mark
UNIPOWER APM110：具有1個最大限制和1個最小限制的Loadmonitor
** 低成本 **
*尺寸：DxWxH = 58 x 70 x 86 mm
*測量和電源電壓：
3 x 380Vac-3 x 500Vac帶一個單元
*通過內部CT直接測量高達80A
-否則外部CT N / 5
*直接測量高達70kW
*范圍=最大限制，以kW為單位設置
：
20％-> 80％的范圍，以4％為步長
*開始時間和反應時間：
0-10秒 （最小限制為20秒）
*手動和自動重置
* CE標志
UNIPOWER APM110: Loadmonitor with 1 Max- and 1 Min-limit
** Low Cost **
* Dimensions: DxWxH = 58 x 70 x 86 mm
* Measuring- and supply voltage:
3 x 380Vac - 3 x 500Vac with one unit
* Direct measurement up to 80A with internal CT
- otherwise external CT N/5
* Direct measurement up to 70kW
* Range = Max-limit, setup in kW
* Min-limit:
20% -> 80% of range in steps of 4%
* Start- and reactiontimers:
0 - 10 sec. (20 sec for Min-limit)
* Manuel and auto-Reset
* CE-mark
UNIPOWER APM110E：具有1個最大限制和1個最小限制的Loadmonitor
** 低成本 **
*尺寸：DxWxH = 58 x 70 x 86 mm
*測量電壓：
3 x 230Vac-3 x 575Vac帶一個單元
* 電源電壓：
1 x 110Vac或1 x 230Vac（帶一個單元）
*可以連接到外接人機界面
-Unipower PCU d10
*作為APM110的功能
* CE標志和cUL批準的Fileno。 E194022
UNIPOWER APM110E: Loadmonitor with 1 Max- and 1 Min-limit
** Low Cost **
* Dimensions: DxWxH = 58 x 70 x 86 mm
* Measuring voltage:
3 x 230Vac - 3 x 575Vac with one unit
* Supply voltage:
1 x 110Vac or 1 x 230Vac with one unit
* May be connected to external display unit
- Unipower PCU d10
* Functionality as APM110
* CE-mark and cUL-approved, Fileno. E194022
UNIPOWER APM300B：千瓦測量傳感器
*尺寸：DxWxH = 58 x 36 x 86 mm
*三相非對稱kW測量
*測量和電源電壓：
可提供3x230Vac-3 x 575Vac
*連接到外部CT-N / 1或N / 5
*精度：符合EN 61036的2級
* 0（4）-20mA以及0（2）-10V模擬輸出
* kWh輸出（SO-1）：
滿量程1000脈沖/小時
*內置濾波器功能-平均16倍
* CE標志
UNIPOWER APM300B: Measurement transducer for kW
* Dimensions: DxWxH = 58 x 36 x 86 mm
* 3-phased asymmetric kW-measurement
* Measuring- and supply voltage:
available from 3x230Vac - 3 x 575Vac
* Connected to external CTs - N/1 or N/5
* Accuracy: Class 2 according to EN 61036
* 0(4)-20mA as well as 0(2)-10V analogue outputs
* kWh-output (SO-1):
1000 pulses/hour at full scale
* Built-in filter function - 16x averaging
* CE-mark
UNIPOWER APM380：千瓦測量傳感器
*尺寸：DxWxH = 58 x 105 x 86 mm
*用于測量的三相非對稱kW-meter
-同樣在變頻器之后
*頻率范圍10Hz-1kHz
*適用于電源電壓：
從3 x 230Vac到3 x 575Vac
*內部可測量高達80A的電流
* 7個標稱電壓范圍
* 10個標稱電流范圍為1A至80A
* 4個可編程模擬濾波器特性
* 3個可編程數字濾波器特性
* 2個模擬輸出（電流隔離）：
0（4）-20毫安
0（2）-10伏
* S0-1輸出為kWh（1或10 imp./kWh）
* CE標志和cUL批準的Fileno。 E350194
UNIPOWER APM380: Measurement transducer for kW
* Dimensions: DxWxH = 58 x 105 x 86 mm
* 3-phased asymmetric kW-meter for measurement
- also after frequency inverter
* Frequency range 10Hz - 1kHz
* Suitable for mains voltages:
from 3 x 230Vac to 3 x 575Vac
* Measures current up to 80A internally
* 7 nominal voltage ranges
* 10 nominal current ranges from 1A to 80A
* 4 programmable analogue filter characteristics
* 3 programmable digital filter characteristics
* 2 analogue outputs (galvanic isolated):
0(4)-20mA
0(2)-10V
* S0-1 output for kWh (1 or 10 imp./kWh)
* CE-mark and cUL-approved, Fileno. E350194
UNIPOWER APM382：千瓦測量傳感器
具有控制功能
*尺寸：DxWxH = 58 x 105 x 86 mm
*具有APM380之類的功能，并具有其他功能：
*通過PC通過RS232進行設置
（包括軟件）
* 2個光耦合器輸出
* 2個獨立限制
* dP / dt監督
*縮放功能：滿刻度= 10-100％
*模擬輸出可能反相：
（20-0（4）mA）
* CE標志和cUL批準的Fileno。 E350194
UNIPOWER APM382: Measurement transducer for kW
with control functions
* Dimensions: DxWxH = 58 x 105 x 86 mm
* Features like APM380 with extra functions:
* Setup via PC over RS232
(Software included)
* 2 optocoupler outputs
* 2 independant limits
* dP/dt supervision
* Zoom function: Full Scale = 10-100%
* Possible inverting of the analogue outputs:
(20 - 0(4) mA)
* CE-mark and cUL-approved, Fileno. E350194
UNIPOWER APM426：用于2速應用程序的負載監視器
*尺寸：DxWxH = 58 x 105 x 86 mm
*通過數字輸入選擇有效極限
*三相非對稱功率計
也用于變頻器后的測量
*適用于電源電壓：
從3 x 230Vac到3 x 575Vac
*內部可測量高達30A的電流
*通過PC通過RS232進行設置
（包括軟件）
* 2個光耦合器輸出
*每個限制的可選類型（最大或最?。?/font>
* CE標志和cUL批準的Fileno。 E350194
UNIPOWER APM426: Load Monitor for 2-speed applications
* Dimensions: DxWxH = 58 x 105 x 86 mm
* Active limit selected via digital input
* 3-phased asymmetric kW-meter
also for measurement after frequency inverter
* Suitable for mains voltages:
from 3 x 230Vac to 3 x 575Vac
* Measures current up to 30A internally
* Setup via PC over RS232
(Software included)
* 2 optocoupler outputs
* Optional type for each limit (Max or Min)
* CE-mark and cUL-approved, Fileno. E350194
UNIPOWER APM450：用于變速應用的負載監控器
*尺寸：DxWxH = 58 x 105 x 86 mm
*取決于速度的設定值
*自動測量速度（頻率）
*三相非對稱功率計
也用于變頻器后的測量
*適用于電源電壓：
從3 x 230Vac到3 x 575Vac
*內部可測量高達30A的電流
*通過PC通過RS232進行設置
UNIPOWER APM450: Load Monitor for variable speed applications
* Dimensions: DxWxH = 58 x 105 x 86 mm
* Speed dependent setpoints
* Automatic measurement of speed (Frequency)
* 3-phased asymmetric kW-meter
also for measurement after frequency inverter
* Suitable for mains voltages:
from 3 x 230Vac to 3 x 575Vac
* Measures current up to 30A internally
* Setup via PC over RS232
(Software included)
* 2 optocoupler outputs
* Two independent limits (Max and Min)
* CE-mark and cUL-approved, Fileno. E350194
UNIPOWER DSU d382：不帶控制功能的人機界面
*尺寸：DxWxH = 70 x 72 x 72 mm
*與APM382一起使用
*通過RS232連接
* APM382編程
*顯示測量結果為kW％
*顯示監督狀態：
-警報條件
-計時器
-輸出位置
